:: [maemo-leste] [PATCH 10/11] Nokia R…
Top Page
Delete this message
Reply to this message
Author: Pali Rohár
To: u-boot
CC: Tom Rini, Simon Glass, Adam Ford, Tony Lindgren, Merlijn Wajer, Arthur D., Pavel Machek, Ivaylo Dimitrov, maemo-leste
Old-Topics: [maemo-leste] [PATCH 00/11] Fixes for Nokia RX-51
Subject: [maemo-leste] [PATCH 10/11] Nokia RX-51: Update README.nokia_rx51
Fix some typos, add information about setup_omap_atag, remove old suff
about ONENAND_SUPPORT and update guide for UBIFS.

Signed-off-by: Pali Rohár <pali@???>
doc/README.nokia_rx51 | 32 +++++++++++++++-----------------
1 file changed, 15 insertions(+), 17 deletions(-)

diff --git a/doc/README.nokia_rx51 b/doc/README.nokia_rx51
index 586ed7c1cc..33c275b416 100644
--- a/doc/README.nokia_rx51
+++ b/doc/README.nokia_rx51
@@ -19,7 +19,7 @@ stored ATAGs (see boot order).
There is support for hardware watchdog. Hardware watchdog is started by
NOLO so u-boot must kick watchdog to prevent reboot device (but not very
often, max every 2 seconds). There is also support for framebuffer display
-output with ANSI espace codes and the N900 HW keyboard input. USB tty works
+output with ANSI escape codes and the N900 HW keyboard input. USB tty works
but is disabled because it prevents the current Maemo kernel from booting.

When U-Boot is starting it enable IBE bit in Auxiliary Control Register,
@@ -36,7 +36,7 @@ Boot from SD or eMMC in this order:

  * 1.
    * 1.1 find boot.scr on first fat partition
-   * 1.2 find uImage on first fat parition
+   * 1.2 find uImage on first fat partition
    * 1.3 same order for 2. - 4. fat partition
  * 2. same as 1. but for ext2/3 partition
  * 3. same as 1. but for ext4 partition
@@ -62,21 +62,26 @@ Available additional commands/variables:
  * run trymmcscriptboot - Try to load and boot script ${mmcscriptfile}
  * run trymmckernboot - Try to load and boot kernel image ${mmckernfile}
  * run trymmckerninitrdboot - Try to load and boot kernel image ${mmckernfile}
-                  with initrd image ${mmcinitrdfile}
+                              with initrd image ${mmcinitrdfile}

Additional variables for loading files from mmc:

* mmc ${mmcnum} (0 - external, 1 - internal)
* partition number ${mmcpart} (1 - 4)
- * parition type ${mmctype} (fat, ext2)
+ * parition type ${mmctype} (fat, ext2, ext4)

-Additional varuables for booting kernel:
+Additional variables for booting kernel:

* setup_omap_atag - Add OMAP table into atags structure (needs maemo kernel)
* setup_console_atag - Enable serial console in OMAP table
* setup_boot_reason_atag - Change boot reason in OMAP table
* setup_boot_mode_atag - Change boot mode in OMAP table

+ Variable setup_omap_atag is automatically set when booting attached kernel.
+ When variable setup_omap_atag is set, variable setup_console_atag is unset
+ and u-boot standard output is set to serial then setup_console_atag is
+ automatically set to 1. So output from Maemo kernel would go to serial port.

Maemo kernel 2.6.28 will crash if u-boot enable usb tty. So USB TTY is disabled.
@@ -85,20 +90,13 @@ USB TTY:

-ONENAND support:
- ONENAND support is disabled because not working yet and cause linux kernel to
- crash or no access to mtd. For enabling ONENAND support add this line at begin
- of file include/configs/nokia_rx51.h
UBIFS support:

UBIFS support is disabled, because U-Boot image is too big and cannot be
flashed with attached zImage to RX-51 kernel nand area. For enabling UBIFS
- support first enable ONENAND support and then add this line at begin of file
- include/configs/nokia_rx51.h
+ support add following lines into file configs/nokia_rx51_defconfig