:: Re: [DNG] Devuan Jessie + Huawei US…
Inizio della pagina
Delete this message
Reply to this message
Autore: info at smallinnovations dot nl
Data:  
To: dng
Oggetto: Re: [DNG] Devuan Jessie + Huawei USB modems
On 27-11-18 13:53, Miroslav Skoric wrote:
> On 11/23/18 5:02 PM, Adam Borowski wrote:
>> On Fri, Nov 23, 2018 at 01:28:00PM +0100, Alessandro Selli wrote:
>>
>>>    Right, many USB modems show up as something different than a
>>> networking device when they are plugged-in.  I haven't used any of them
>>> for a long time, but I remember many of them show up as a CDROM device
>>> which carries the Windows drivers and/or some Windows utility.  The
>>> actual modem shows up after the CDROM device is unmounted or ejected.
>>
>> Ie, usbmodeswitch.  This might or might not work with modemmanager --
>> in my
>> experience, it works _randomly_.  Including having the dongle suddenly
>> switch while the connection is running, with obviously fatal
>> results.  And
>> modemmanager seems to be unable to recover.
>>
>
> Ok, today I paid a visit to the seniors' club to see what can be done.
> I found their old USB stick modem, inserted it into the Devuan box ...:
>
> root@devuan:~# lsusb
> Bus 002 Device 005: ID 19d2:0017 ZTE WCDMA Technologies MSM
> Bus 002 Device 003: ID 0951:1642 Kingston Technology DT101 G2
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 003 Device 002: ID 0000:3825
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> root@devuan:~# usb_modeswitch -v 19d2 -p 0017
> Look for default devices ...
>    product ID matched
>  Found devices in default mode (1)
> Access device 005 on bus 002
> Current configuration number is 1
> Use interface number 0
>
> USB description data (for identification)
> -------------------------
> Manufacturer: ZTE,Incorporated
>      Product: ZTE WCDMA Technologies MSM
>   Serial No.: MF6670VIPD010000
> -------------------------
> Warning: no switching method given. See documentation
> -> Run lsusb to note any changes. Bye!
>
> root@devuan:~#
>
>
> ... then I tried again but with some more options:
>
>
> root@devuan:~# usb_modeswitch -v 19d2 -p 0017 -K
> Look for default devices ...
>    product ID matched
>  Found devices in default mode (1)
> Access device 005 on bus 002
> Current configuration number is 1
> Use interface number 0
> Use endpoints 0x01 (out) and 0x81 (in)
>
> USB description data (for identification)
> -------------------------
> Manufacturer: ZTE,Incorporated
>      Product: ZTE WCDMA Technologies MSM
>   Serial No.: MF6670VIPD010000
> -------------------------
> Sending standard EJECT sequence
> Looking for active driver ...
>  OK, driver detached
> Set up interface 0
> Use endpoint 0x01 for message sending ...
> Trying to send message 1 to endpoint 0x01 ...
>  OK, message successfully sent
> Read the response to message 1 (CSW) ...
>  Response reading failed (error -7)
>  Device is gone, skip any further commands
> -> Run lsusb to note any changes. Bye!
>
> root@devuan:~# lsusb
> Bus 002 Device 005: ID 19d2:0017 ZTE WCDMA Technologies MSM
> Bus 002 Device 003: ID 0951:1642 Kingston Technology DT101 G2
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 003 Device 002: ID 0000:3825
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> root@devuan:~# usb_modeswitch -v 19d2 -p 0017 -K -R
> Look for default devices ...
>    product ID matched
>  Found devices in default mode (1)
> Access device 009 on bus 002
> Current configuration number is 1
> Use interface number 0
> Use endpoints 0x01 (out) and 0x81 (in)
>
> USB description data (for identification)
> -------------------------
> Manufacturer: ZTE,Incorporated
>      Product: ZTE WCDMA Technologies MSM
>   Serial No.: MF6670VIPD010000
> -------------------------
> Sending standard EJECT sequence
> Looking for active driver ...
>  OK, driver detached
> Set up interface 0
> Use endpoint 0x01 for message sending ...
> Trying to send message 1 to endpoint 0x01 ...
>  OK, message successfully sent
> Read the response to message 1 (CSW) ...
>  Response reading failed (error -7)
>  Device is gone, skip any further commands
> Device handle empty, skip USB reset
> -> Run lsusb to note any changes. Bye!
>
> root@devuan:~#
>
>
> ... seems that -K (eject memory stich driver) and -R (reset) did not
> change much (if anything). Any idea?
>
>>>     The package modemmanager is supposed to take care of the correct
>>> initialization of a number of known and supported modems using udev's
>>> rules (the ASCII package install 18 such rules).  Yet, I think
>>> sometimes
>>> human intervention is still needed, and of course several USB modems
>>> (as
>>> well as PCMCIA/CardBus ones and some WiFi dongles and Access Points)
>>> are
>>> partially, poorly or not supported at all.
>>
>> Alas, we're deeply in the "sacrifice a young black goat" land.  The
>> quality
>> of drivers, firmware and _hardware_ is so egregious that it's far more
>> effort effective to take an old phone and set up tethering.
>>
>
> There is no modemmanager there, as well as no vwdial, ppp, etc
> installed per default in this Devuan distro. I will have to download
> .deb packages elsewhere and bring them here to continue ...
>
> Misko
> ______


It is a while ago that I struggled with a USB modem but your device
should be recognized by your system (supported since 2.6.18).

A old bug i found was that usbstorage is too fast for usbswitch. The
remedy would be to create a file /etc/modprobe.d/usb-storage.conf:

options usb-storage delay_use=3


or a higher number.


Grtz

Nick