:: Re: [Dng] No way to use a prepartio…
Página Principal
Delete this message
Reply to this message
Autor: Richard
Data:  
Para: dng
Assunto: Re: [Dng] No way to use a prepartioned disk?
On Mar 2, 2015 10:41 AM, "Richard" <richard.holt@???> wrote:
>
>
> On Mar 1, 2015 6:26 PM, "fsmithred" <fsmithred@???> wrote:
> >
> > >
> > > On 03/01/2015 04:41 PM, Hendrik Boom wrote:> On Sun, Mar 01, 2015 at

05:44:47PM +0000, Hendrik Boom wrote:
> > >>> I tried using the valentine installer on a disk that already had

three
> > >>> primary partitions and a lot of empty space.
> > >>
> > >> In case it's relevant, I was using the expert install, wanting to

make
> > >> my own paritioning decisions. That's what I usually do when

installing
> > >> Debian. Was this a mistake?
> > >>
> > >> -- hendrik
> > >>
> >
> >
> >
> > The first time I installed the valentine preview, it was on existing
> > partitions in a virtualbox VM. I chose a regular (non-expert)install,
> > chose manual partitioning.
> >
> > When the partitioner showed me the existing partitions, I noticed that
> > there were two partitions instead of one. There was a swap partition
> > inside an extended partition, which I'm sure I did not create. Other

than
> > that, the installation went fine.
> >
> > I then booted the VM with a live CD and repartitioned the drive using
> > gparted. Made a single partition again, then rebooted the valentine iso

to
> > see if the same thing would happen, but it did not. I could not

reproduce
> > it. I even tried a third time.
> >
> > Except for that first install, the partitioner did what I expected it to
> > do - it showed me the existing partitions and allowed me to choose

whether
> > to use them or not.
> >
> > fsr
> >
> > >>
> > >> I could not get manual partitioning to leave the existing partitions
> > >> alone and install devuan to secondary partitions in the empty

space. The
> > >> closest I could get was a question whether I'd like it to replace the
> > >> existing partition table with a new empty one. Of course I answered
> > >> 'no'. I wanted it to start from the existing partition structure.
> > >> 'yes' seemed somewhat dangerous.
> > >>
> > >> Well, in reality, those partitions wera a copy of files I had

elsewhere
> > >> and wanted to be able to use on the new system in a dual-boot
> > >> configuration, so in theory I could have gone further and restored

those
> > >> partition later, and when I have time I may still do that to further

test
> > >> the installer. But I'd rather test how well int cooperates with

other
> > >> existing systems.
> > >>
> > >> -- hendrik
> > >>
> > >> _______________________________________________
> > >> Dng mailing list
> > >> Dng@???
> > >> https://mailinglists.dyne.org/cgi-bin/mailman/listinfo/dng
> > > _______________________________________________
> > > Dng mailing list
> > > Dng@???
> > > https://mailinglists.dyne.org/cgi-bin/mailman/listinfo/dng
> > >
> >
> > _______________________________________________
> > Dng mailing list
> > Dng@???
> > https://mailinglists.dyne.org/cgi-bin/mailman/listinfo/dng
>
> Installing Valentine on HD on AA1:
> 1. First three attempts failed. 1st with the GUI and then with the curses

version.
> Each picked up and connected to wifi.
> 2. All stopped at 33% of formatting the chosen partition. I waited at

least 15 minutes for each.
> 3. Formatted the desired partition with gparted then ran the curses

installer without doing any partitioning. Valentine is happily installing
at the moment.
> 4. I'll give it a bit more use this time. Previously just wanted to see

the shape of things to come.

Note: Installed to MBR of HD. Only needs reinstall grub2 to return to
previous setup.