:: Re: [dyne:bolic] 2.2 XRUNS !!!
Αρχική Σελίδα
Delete this message
Reply to this message
Συντάκτης: Andy Frisko
Ημερομηνία:  
Προς: dynebolic mailinglist
Αντικείμενο: Re: [dyne:bolic] 2.2 XRUNS !!!
thanks for the tips :)

i tried 64studio and i can't remember properly but i think i tried demudi too
but i had sata problems ... my hdd wasn't detected and i didn't want to waste so much time to figure it out ... or get a driver ...

dynebolic worked verygood from cd.
over 10 minutes @ 12 tracks i had no xruns. (with 2.1)

but after i docked and nested 2.2
i got alot more ... :(

thanks, bye.


> Eduard,
>
> If you're serious about setting up a music studio with Linux, you might do
> better to use a regular distribution rather than a nomadic distribution
> (CD-based). Dyne:bolic is tailored more for independent journalists than
> music producers. There are a number of good music distributions, some of
> them more complicated than others: Musix, Studio-to-go (non-free), Demudi,
> and the new 64studio (which I use). The last two have a realtime-patched
> kernel which is key for audio work.
>
> That said, if you're sticking with dyne:bolic for this project, here's my
> advice: More RAM would be great. 512mb is going to be handy if you're
> recoding 12 tracks at once at that resolution. Even docked, I think
> (correct me if I'm wrong) that some of your RAM is being sucked up by a
> ramdisk with Dyne. Also, even with a realtime kernel, my jack buffer is
> set
> to 4 to completely avoid xruns, so try that. If your interface supports
> hardware monitoring, that's always the best solution, as it's zero-latency
> by design. Unless you're using soft-synths too, you won't notice the
> difference. The biggest difference is going to be setting jack to it's
> optimal settings.
>
> Good luck,
> Clem
>
>
> On 10/9/06, Andy Frisko <darthvim@???> wrote:
> >
> > (sorry first one was sent wrong ...)
> > hi,
> >
> > Today I tried out dynebolic 2.2 on my PC. I have an
> > amd athlon 2600+
> > 512MB RAM
> > SATA 120 GB seagate harddisk
> >
> > Jack:
> > 48 KHz
> > 128 Frames
> > Buffer 2
> > Realtime
> >
> >
> > Sound Card:
> > RME HDSP 9652
> > with 1.3 MS minimum latency
> >
> > In Windows with ASIO I had no problems but with dynebolic 2.2 Jack and
> > Ardour I get Xruns.
> > I recorded 12 tracks at the same time for half an hour and I got 254
> > Xruns. This seems to be not a good rate for recording audio.
> > On ubuntustudio.com was written that you should only have Xruns on
> > programm start up.
> > My nest is about 350 MB and dynebolic and my audio directory is on the
> > same partition. Can you help me to eliminate Xruns, please?
> >
> > Thanks
> > In advance
> > Eduard
> >
> > --
> > Der GMX SmartSurfer hilft bis zu 70% Ihrer Onlinekosten zu sparen!
> > Ideal für Modem und ISDN: http://www.gmx.net/de/go/smartsurfer
> > _______________________________________________
> > dynebolic mailing list
> > dynebolic@???
> > http://mailinglists.dyne.org/mailman/listinfo/dynebolic
> >


--
GMX DSL-Flatrate 0,- Euro* - Überall, wo DSL verfügbar ist!
NEU: Jetzt bis zu 16.000 kBit/s! http://www.gmx.net/de/go/dsl